Steel rails support the locomotive and guide its direction, and the rail is fixed on the sleeper of the roadbed through elastic fasteners. The fastening parts of an elastic fastener are mainly elastic clips, which apply stress and force on the track through bending and twisting deformation. They ensure a reliable connection between the rail and the sleeper, prevent vertical and horizontal movement of the rail relative to the sleeper, and maintain the correct gauge for safe train operation. This article focuses on elastic rail clips manufactured from 55Si2Mn and 38Si7 spring steel with a hardness of 44 to 48 HRC.
Why Spring Steel Is Used for Rail Clips
Because the contact between the rail wheel and the rail is rigid, vibration is inevitable during train passage. The special elastic structure of the clips absorbs part of the impact energy and provides damping. Elastic clips work under alternating repeated stress, and are subjected to bending, torsion, fatigue and corrosion, as well as very high instantaneous impact loads when trains pass. The performance requirements for elastic clips are therefore very strict, and spring steel with high elastic limit, high yield strength and excellent fatigue resistance is required.
Chemical Composition of 55Si2Mn and 38Si7
| Element | 55Si2Mn | 38Si7 |
|---|---|---|
| Carbon | 0.52-0.60% | 0.35-0.42% |
| Silicon | 1.50-2.00% | 1.50-1.80% |
| Manganese | 0.60-0.90% | 0.50-0.80% |
| Chromium | ≤0.35% | not specified |
| Phosphorus | ≤0.03% | ≤0.03% |
| Sulfur | ≤0.03% | ≤0.03% |
The high silicon content in both grades raises the elastic limit and improves the fatigue resistance of the spring steel, while the carbon content controls the hardenability and strength after heat treatment. Other grades used for elastic rail clips include 60Si2MnA and 60Si2CrA with similar composition ranges, and the reference standards include DIN 17221, BS 970 and GB/T 1222.
Hardness and Fatigue Performance
Elastic clips are hardened and tempered to a hardness of 44 to 48 HRC for E-type clips and 42 to 47 HRC for tension type clips. At this hardness, the clips provide the required clamping force while maintaining sufficient toughness to avoid brittle fracture. Under fatigue testing, clips of 18 mm wire diameter withstand 3 million cycles without breaking, and clips of 20 mm diameter withstand 5 million cycles without breaking. The combination of correct hardness and surface quality is essential for achieving these fatigue results.
Common Clip Models and Dimensions
Elastic rail clips are supplied in a wide range of models with wire diameters from 13 mm to 20 mm. Light clips of 13 mm diameter weigh about 0.25 to 0.53 kg per piece, while medium clips of 18 mm diameter weigh about 0.58 to 0.62 kg, and heavy clips of 20 mm diameter weigh about 0.80 to 1.03 kg. Common examples include E1809 with 20 mm diameter, E1813 with 18 mm diameter, E2001, E2039 and E2055 with 20 mm diameter, and heavy clips of 20 mm diameter with weights around 0.85 to 1.03 kg. Clips can also be manufactured exactly according to customer designed drawings and requirements.
Clip Models, Dimensions and Surface Treatment
Surface treatments include plain oiled finish, oxide black, color painting, hot-dip galvanizing and zinc plating. The plain oiled and oxide black finishes are economical for dry climates, while hot-dip galvanizing is recommended for humid, coastal and industrial environments. The surface treatment must not affect the fatigue performance of the spring steel; therefore, processes that could introduce hydrogen embrittlement are controlled carefully.
Elastic rail clips are used in railway fastening systems on main lines, secondary lines, mining railways, crane tracks and urban transit systems worldwide. They work together with base plates, rail pads, insulators and screw spikes to form a complete fastening system on wooden or concrete sleepers. The correct combination of clip model, rail section and sleeper type must be verified by the system design, because the clamping force and toe load must match the service conditions.
Inspection and Maintenance
Inspect clips regularly for cracks, corrosion, loss of clamping force and displacement. Use the correct installation tool and avoid impact loading, which can create micro cracks in the spring steel. Replace damaged clips promptly and check the torque of the associated screw spikes. In corrosive environments, upgrade the surface protection and inspect the clips more frequently.
Frequently Asked Questions
What is the difference between 55Si2Mn and 38Si7? 55Si2Mn has higher carbon of 0.52-0.60 percent, while 38Si7 has lower carbon of 0.35-0.42 percent; both are silicon spring steels with high elastic limit.
What hardness do elastic rail clips have? E-type clips are heat treated to 44-48 HRC, and tension type clips to 42-47 HRC.
What is the fatigue life of the clips? Clips of 18 mm diameter withstand 3 million cycles and clips of 20 mm diameter withstand 5 million cycles without breaking.
Which standards are referenced for clip material? DIN 17221, BS 970 and GB/T 1222 for the spring steel material and quality.
Why is high silicon content important? Silicon raises the elastic limit and improves fatigue resistance, which are essential for clips working under repeated bending stress.
Can clips be made to customer drawings? Yes, elastic rail clips can be manufactured exactly according to customer designed drawings and requirements.






