A rail anchor is used to clamp onto the base of the rail snug against the crosstie on both sides. It is produced in one piece from spring steel or other suitable material, with the aim of eliminating track sliding, expansion or contraction. Rail anchors fasten the rail tight on the base of the rail to prevent longitudinal movement of the rail relative to the sleeper, which is essential for continuous welded rail and jointed track stability.
Function of Rail Anchors
Rail anchors are applied to the rail base directly and provide a large bearing surface against the rail base and the rail tie, preventing wear and cutting, and eventually prolonging the working life of the rail ties. They restrain the rail from creeping under traffic, which is caused by the repeated acceleration and braking forces of trains. Without anchors, rail creep can push the track out of alignment, close expansion joints and damage sleepers and ballast. According to the specific rail weight and base width, anchors can be classified into two types: drive-on rail anchors and spring type rail anchors.
Materials Used for Rail Anchors
The most common materials for rail anchors are 60Si2MnA spring steel, 45# carbon steel and QT500-7 ductile iron. 60Si2MnA is a silicon-manganese spring steel with carbon 0.56 to 0.64 percent, silicon 1.60 to 2.00 percent and manganese 0.60 to 0.90 percent, providing high elastic limit and fatigue resistance for spring type anchors. 45# carbon steel has carbon 0.42 to 0.50 percent, silicon 0.17 to 0.37 percent and manganese 0.50 to 0.80 percent, offering good strength and toughness for drive-on anchors. QT500-7 is a ductile iron with carbon 3.60 to 3.80 percent, silicon 2.50 to 2.90 percent and manganese not more than 0.60 percent, providing a tensile strength of at least 500 MPa and an elongation of at least 7 percent, and is used where casting shapes are preferred.
Types of Rail Anchors
Drive-on rail anchors are driven onto the rail base with a hammer or special tool and are held in place by friction and spring action. Spring type rail anchors are installed by springing them onto the rail base and provide consistent holding force. Both types are designed to fit the rail base of specific rail sections, such as 50 kg/m, 85 kg/m, 90/91 lb, 115RE, 136RE, UIC54 and UIC60 rails, or other types according to customer drawings. Anchors with consistent style and high quality provide the right rail fit and higher longitudinal keeping power.
Performance Requirements
Rail anchors must provide high longitudinal keeping power to resist rail creep, be fast and simple to install, and be safe to handle at the track site. One-piece construction from spring steel eliminates loose parts and ensures reliable performance. ISO 9001 certified manufacturing with controlled heat treatment guarantees consistent quality. The surface is typically plain oiled, color painted, zinc painted or hot-dip galvanized to resist corrosion.
Standards, Applications, Installation and Maintenance
Rail anchors are manufactured according to standards such as AS 1085.10, DIN and ISO 9001 quality systems, and are available for various rail types and service conditions, from heavy-haul main lines to light industrial tracks. They are used on continuous welded rail, where they prevent the rail from expanding or contracting along the track, and on jointed track to keep the rail joints tight.
Install drive-on anchors with the correct tool, positioning them snug against the tie so that they press the rail base firmly. Spring anchors are installed with a lever tool and must be fully seated to develop their holding force. During inspection, check anchors for loosening, deformation and corrosion, and reseat or replace them as required. In areas with heavy rail creep, install anchors on both sides of the tie and inspect them more frequently.
Frequently Asked Questions
What is the function of a rail anchor? It clamps onto the rail base against the tie to prevent longitudinal rail movement caused by train traffic and temperature changes.
What materials are used for rail anchors? 60Si2MnA spring steel, 45# carbon steel and QT500-7 ductile iron are the most common materials.
What is the difference between drive-on and spring rail anchors? Drive-on anchors are hammered onto the rail base, while spring anchors are sprung into position; both provide longitudinal holding force.
What is QT500-7 ductile iron? It is a ductile iron with a tensile strength of at least 500 MPa and an elongation of at least 7 percent, used for cast anchor shapes.
Which rail sections do anchors fit? Common sections include 50 kg/m, 90/91 lb, 115RE, 136RE, UIC54 and UIC60 rails, or other types per customer drawings.
Why is one-piece construction important? One-piece construction from spring steel eliminates loose parts, improves reliability and makes installation fast and safe.






