Components and Functions of the E-Clip Railway Fastening System

Oct 29, 2025 Leave a message

The E-clip railway fastening system is a mature fastening design that can be used on almost all kinds of rail sections, and it is now widely installed in railway projects around the world. A complete E-clip fastening assembly consists of two elastic rail clips, two rail shoulders, one rail pad and two rail insulators. This article introduces each component and its function.

What Is an E-Clip Fastening System

The E-clip fastening system holds the rail foot down on the sleeper or baseplate while allowing controlled vertical elasticity. It suits UIC54, UIC60, 115RE, BS80A, BS100A, 50 kg and 60 kg rails and many other sections, because the shoulder and the clip can be matched to the rail foot profile. The system provides a defined toe load, electrical insulation and protection against longitudinal rail movement, which makes it suitable for ballasted track, slab track, turnouts and crane runways alike.

System Components and Quantities

Component Quantity Material Function
E-clip 2 60Si2MnA, 60Si2CrA Presses the rail foot down with a defined toe load
Rail shoulder 2 Ductile iron QT500-7, QT450-10 Anchors the clip and resists longitudinal and lateral forces
Rail pad 1 HDPE, rubber or EVA Cushions the rail, protects the sleeper, controls stiffness
Rail insulator 2 Reinforced nylon PA66 Provides electrical insulation and gauge positioning

E-Clip Toe Loads by Wire Diameter

The toe load of the E-clip increases with the wire diameter. For a 16 mm clip the toe load is typically 500 to 700 kgf, for an 18 mm clip 750 to 900 kgf, and for a 20 mm clip 1100 to 1400 kgf. These values are about 4.9 to 6.9 kN, 7.4 to 8.8 kN and 10.8 to 13.7 kN respectively. The clips are heat-treated to a hardness of 44 to 48 HRC and tested to 5 million fatigue cycles without breaking, in accordance with spring steel standards such as DIN 17221, BS 970 and GB/T 1222.

Materials of Each Component

The E-clip itself is made of silicon-manganese spring steel such as 60Si2MnA or 60Si2CrA, with a wire diameter of 16, 18 or 20 mm, for example E1809, E2006, E2007 or E2009. The shoulder is cast in ductile iron QT500-7 or QT450-10, which gives the necessary strength and toughness for anchoring the clip. The rail pad is made of HDPE, rubber or EVA and cushions the rail foot. The rail insulator is moulded from reinforced nylon 66, which provides high mechanical strength and stable electrical insulation between the rail and the fastening.

How the System Works Together

When the clip is driven into the shoulder, its legs deflect and press the rail foot down through the pad. The shoulder resists the longitudinal forces from train braking and acceleration, and the insulator keeps the rail electrically isolated from the sleeper so that track circuits work correctly. The pad maintains intimate contact with the rail under the clip toe load and limits deflection under the wheel. Together the four component types form a complete, replaceable fastening unit that keeps the gauge stable and the rail secure for the whole service life.

Frequently Asked Questions

How many components are in one E-clip fastening assembly? complete assembly contains two clips, two shoulders, one rail pad and two insulators, seven pieces in total per rail seat.

What material are the rail shoulders made of? The shoulders are cast in ductile iron QT500-7 or QT450-10.

What is the toe load of a 20 mm E-clip? The toe load is typically 1100 to 1400 kgf, about 10.8 to 13.7 kN.

Why is the insulator made of nylon 66? Reinforced nylon 66 gives high mechanical strength and stable electrical insulation between the rail and the fastening.

Which rail sections can use the E-clip system? The system suits most flat-bottom rails, including UIC54, UIC60, 115RE, BS80A, BS100A, 50 kg and 60 kg rails.