What a Rail Anchor Must Withstand
A rail anchor, also described as an anti-creeper, is a spring steel clamp fixed under the rail foot that bears against the sleeper face to stop longitudinal rail movement. Movement is generated by thermal expansion and contraction, by traction and braking forces, and by vibration transmitted through the track. The anchor is therefore loaded in tension along the rail direction on every wheel passage and must hold a near constant jaw force for years without cracking or relaxing.
Three material families are used in practice: quality carbon steels, manganese and silicon-manganese spring steels, and ductile iron for certain casting based designs.
Carbon and Medium Carbon Steels
Grade 45 steel to GB/T 699 is a quality carbon structural steel with a typical composition of carbon 0.42 to 0.50 percent, silicon 0.17 to 0.37 percent, manganese 0.50 to 0.80 percent, chromium 0.25 percent maximum, phosphorus 0.035 percent maximum and sulphur 0.035 percent maximum. After quenching and tempering it develops enough strength and hardness for anchor bodies and jaws, while retaining the toughness needed to survive ballast tamping. Medium carbon grades of this family are also used for anchor components that are not required to act as springs.
Manganese and Silicon Manganese Spring Steels
Where elastic jaw force is the design driver, manganese and silicon-manganese spring steels are selected. Grades such as 40Mn and 50Mn provide a balance of hardenability and cost, while 60Si2Mn or 60Si2MnA to GB/T 1222 delivers the high elastic limit and fatigue resistance expected of a spring component. The typical composition of 60Si2MnA is carbon 0.56 to 0.64 percent, silicon 1.60 to 2.00 percent, manganese 0.60 to 0.90 percent, chromium 0.35 percent maximum, phosphorus 0.03 percent maximum and sulphur 0.03 percent maximum. The silicon addition is what raises the elastic limit; the manganese improves hardenability so that a heavy section can be through hardened rather than only surface hardened.
Ductile Iron Options
Ductile iron grade QT500-7 to GB/T 1348 is used for cast anchor designs and for related track hardware. The standard specifies a minimum tensile strength of 500 MPa, a minimum 0.2 percent proof strength of 320 MPa and a minimum elongation of 7 percent, with typical composition ranges of carbon 3.60 to 3.80 percent, silicon 2.50 to 2.90 percent, manganese 0.60 percent maximum, phosphorus 0.08 percent maximum and sulphur 0.025 percent maximum. The nodular graphite structure gives damping and toughness, which suits components exposed to impact in the ballast shoulder, but the spring force available is lower than from a hardened spring steel jaw.
Material and Property Summary
| Material | Standard | Key property | Typical role |
|---|---|---|---|
| 45 | GB/T 699 | C 0.42 to 0.50, Mn 0.50 to 0.80 | Body and non-spring components |
| 55 | GB/T 699 | Higher carbon content for greater strength | Components needing extra wear resistance |
| 40Mn, 50Mn | GB/T 699 | Manganese improves hardenability | Medium duty jaws |
| 60Si2Mn, 60Si2MnA | GB/T 1222 | Si 1.60 to 2.00 for high elastic limit | Spring jaws carrying sustained force |
| QT500-7 | GB/T 1348 | 500 MPa tensile, 320 MPa proof, 7 percent elongation | Cast anchor and hardware designs |
Heat Treatment and Its Effect on Jaw Force
Spring steel anchors are austenitised, quenched and tempered, and the tempering temperature is chosen as a compromise between jaw force and fatigue resistance. Higher hardness increases gripping force but lowers toughness, which raises the risk of cracking at the bend radii; lower hardness improves ductility but allows the jaw to relax in service. Hardness and microstructure are therefore verified on finished parts rather than only on test coupons, and a hardness traverse across the jaw is the usual acceptance check. Ductile iron parts are controlled instead through casting soundness, nodularity and tensile testing of separately cast test pieces.
Rail Section Matching and Coating
Anchor geometry is rail specific: units are produced for 50 kg/m, 85 kg/m, 90 lb and 91 lb, 115RE and 136RE, and UIC54 and UIC60 sections, with further designs made to drawing. Fitting an anchor intended for one foot width onto another section reduces contact area and jaw force, which is why the rail section is normally stated on the purchase order alongside the material grade. Corrosion protection is typically hot dip galvanising to ISO 1461, where a steel thickness of 6 mm and above requires a minimum average coating of 85 micrometres and a minimum local coating of 70 micrometres, or a zinc rich paint system selected for the corrosivity category of the site.
Frequently Asked Questions
Q: What material is normally used for rail anchors?
A: Medium and high carbon steels such as grade 45 and 55 to GB/T 699, manganese and silicon-manganese spring steels such as 40Mn, 50Mn, 60Si2Mn and 60Si2MnA, and ductile iron QT500-7 to GB/T 1348 for cast designs.
Q: Why is silicon added to spring steel for anchors?
A: Silicon raises the elastic limit and improves resistance to relaxation, so the jaw keeps its gripping force instead of relaxing under sustained load. Typical silicon content in 60Si2MnA is 1.60 to 2.00 percent.
Q: Which rail sections can anchors be supplied for?
A: Common sections include 50 kg/m, 85 kg/m, 90 and 91 lb, 115RE, 136RE, UIC54 and UIC60, with special designs produced to drawing for other profiles.
Q: How is jaw force controlled in production?
A: By matching the steel grade and section to the design, by controlling quenching and tempering, and by verifying hardness and, where specified, jaw opening force on finished parts.
Q: What coating is applied for corrosion protection?
A: Hot dip galvanising to ISO 1461 is standard, with a minimum average coating of 85 micrometres for steel 6 mm and above, and painted zinc rich systems are used where a specific corrosivity category has to be met.
Q: What is the difference between a spring steel anchor and a ductile iron anchor?
A: A spring steel anchor stores energy in a hardened elastic jaw and produces higher gripping force, while a ductile iron anchor relies on casting geometry and offers good toughness and damping but lower spring force.






