What Is P75 Rail?
P75 rail is the heaviest profile in the Chinese GB heavy rail range, with a nominal mass of 75 kg per metre. It is hot rolled from high-carbon, high-manganese rail steel to standard GB 2585-2007 and is normally supplied in bar lengths from 12 m to 25 m. With a rail height of 192 mm and a web thickness of 20 mm, the section carries a far larger second moment of area than the 38 kg/m, 43 kg/m, 50 kg/m and 60 kg/m profiles, so it deflects less under the same wheel load. That stiffness is what makes it the natural choice for mine roadways, industrial sidings and crane tracks where axle loads are high and the trackbed is less than ideal.
P75 Rail Dimensions and Technical Data
| Parameter | Value |
|---|---|
| Standard | GB 2585-2007 |
| Nominal weight | 75 kg/m |
| Actual unit mass | 74.41 kg/m |
| Rail height | 192 mm |
| Head width | 75 mm |
| Base width | 150 mm |
| Web thickness | 20 mm |
| Standard length | 12 m - 25 m |
| Steel grades | 50Mn, U71Mn |
| Typical use | Mine haulage, factory track, crane runway |
How P75 Compares with the Rest of the Heavy Rail Family
The GB heavy rail series steps up in mass and stiffness from 38 kg/m to 75 kg/m. The table below lists the nominal cross-section data that design engineers use when selecting a profile for a given axle load and sleeper spacing.
| Size | Rail height (mm) | Base width (mm) | Head width (mm) | Web thickness (mm) | Weight (kg/m) |
|---|---|---|---|---|---|
| 38 kg | 134 | 114 | 68 | 13 | 38.73 |
| 43 kg | 140 | 114 | 70 | 14.5 | 44.65 |
| 50 kg | 152 | 132 | 70 | 15.5 | 51.51 |
| 60 kg | 176 | 150 | 73 | 16.5 | 60.64 |
| 75 kg | 192 | 150 | 75 | 20 | 74.41 |
Material Grades: 50Mn and U71Mn
Two rail steel grades are normally rolled for this profile. 50Mn is a medium-carbon manganese steel that offers good through-hardening and a favourable balance between strength and ductility, which suits general industrial track and moderate curves. U71Mn is a higher-carbon manganese rail steel developed for wear resistance and fatigue performance on lines carrying heavy axle loads and dense traffic. Both grades are produced by basic oxygen or electric furnace melting followed by continuous casting, and the finished rail is straightened, ultrasonically inspected for internal defects and cut to the ordered length. End drilling, cambering and head hardening can be carried out to suit the joint or welding method used on site.
Typical Applications
Mine haulage roadways with steep gradients and heavy traffic
Factory and workshop internal track laid on simple, stiff foundations
Crane runway and hoisting equipment tracks, where rail deflection must stay small
Heavy-haul connecting lines and loading yard tracks
Port, steel mill and power station internal rail systems
The benefit is consistent: a deep, heavy section lowers rail bending stress, reduces the pressure transmitted to the sleeper and ballast, and keeps the running surface flatter for longer. On poor foundations this usually extends the tamping cycle and reduces the frequency of rail replacement.
Selecting, Cutting and Installing 75 kg/m Rail
Because the section is heavy, handling and installation need planning. Rails are usually lifted in matched bundles, and mechanical handling equipment should be rated for the bar mass over the ordered length. Cutting is best done by abrasive disc or rail saw rather than thermal methods, so that the cut end stays square and free of metallurgical damage before drilling or welding. Drill holes should be deburred and chamfered, and when the rail is to be welded into continuous track the ends must be prepared to the welding procedure specified for the grade. Matching accessories - heavy duty fish plates, base plates, rail clips, bolts and insulating components - should be selected for the same 75 kg/m section so that the clamping force and gauge tolerance are maintained across the whole track.
Frequently Asked Questions
Q: What is the difference between 75 kg/m rail and P75 rail?
They refer to the same profile. P75 is the profile designation used in the Chinese GB heavy rail series and 75 kg/m describes its nominal mass per metre. The actual rolled unit mass is about 74.41 kg/m.
Q: Which standard applies to this rail?
GB 2585-2007 is the Chinese standard for hot rolled railway rails, and it governs the dimensions, tolerances and steel grades of the 75 kg/m heavy rail profile.
Q: Why is the web 20 mm thick on the 75 kg profile?
The thicker web raises the shear capacity and the stiffness of the section, which limits deflection and reduces the stress transferred to sleepers when the rail is used on mine roadways, crane tracks and other heavy industrial installations.
Q: What lengths are available?
Standard delivery is 12 m to 25 m. Shorter lengths for crane runways and curved industrial track, and longer lengths for welding into continuous track, can be produced on request.
Q: Can the rail be supplied drilled and cambered?
Yes. Holes for fish plates and end preparation can be machined to the drawing supplied by the customer, and cambered ends are available when the track is to be jointed rather than welded.
Q: How should P75 rail be stored before installation?
Store bundles on timber bearers on firm, drained ground, keep the rail heads clear of standing water, and avoid stacking height that could bend or scratch the running surface.






