What Is a Rail Fastening System?
A rail fastening system is used for fastening the steel rail and the railway sleeper. The function of the rail fastening system is to maintain the gauge and prevent the vertical and horizontal movement of rails relative to the position of the sleeper. A fastening system usually consists of a rail tie plate, spike, clip, rail anchor, rail fish plate and other fasteners. Every component has its own role: the tie plate spreads the load, the clip applies the clamping force, the spike or bolt fixes the assembly to the sleeper, the anchor controls longitudinal movement, and the fish plate connects the rail ends.
Main Types of Fastening Systems
Different track conditions need different fastening solutions. The clip type fastening system uses an elastic clip to clamp the rail foot onto the base plate and is the most widely applied design for mainline track. The tension clamp fastening system uses a spring clamp with screw spikes and is popular on concrete sleeper lines. The spring blade fastening system uses a blade-shaped spring element and suits lighter track structures. These systems can be supplied for high speed rail track, normal rail track or subway lines, and each one is matched to the rail section, the sleeper type and the required clamping performance.
Range of Railway Fastener Products
A complete railway fastener programme covers the following product families.
| Category | Typical Products |
|---|---|
| Spikes and screws | Railway screw spike, dog spike, sleeper screw, rail screw and spike |
| Clips and clamps | Elastic rail clip, tension clamp, spring clamp, rail clamp |
| Bolts | High tensile bolt with nut and washer, fish bolt with nut and washer, track bolt |
| Plates | Rail base plate, tie plate, rail fixing base, sole plate |
| Joints | Rail fish plate, joint bar, splice bar, rail joint |
| Other fastening parts | Rail shoulder, rail dowel, plastic ferrule, rubber and EVA pad, spring washer |
| Rails | Crane rail, light rail and associated accessories |
How the Components Work Together and Selection Points
In a typical fastening set, the rail pad sits between the rail foot and the tie plate to provide elasticity and protection. The clip presses the rail foot down on the plate, the shoulder transfers the clamping force into the sleeper, and the screw spike or bolt fixes the whole assembly. The fish plate connects adjacent rail ends so that the track remains continuous, and the rail anchor resists the longitudinal creep caused by temperature changes and braking forces. All components must be matched to each other and to the rail section, otherwise the fastening will not hold the specified toe load and the track geometry will not stay stable.
For high speed rail track, select a fastening system with high clamping stability, low dynamic stiffness and proven fatigue life, and use screw spikes with plastic ferrules on concrete sleepers. For normal rail track, the clip type fastening system is the standard choice, with components matched to the rail mass per metre. For subway and urban rail, pay special attention to vibration and noise isolation, and use rail pads with suitable stiffness. In every case, confirm the standard of the rail, the sleeper spacing and the required gauge before ordering.
Quality Control and Common Misconceptions
Railway fasteners must be produced with traceable quality control. Raw materials should be verified by batch number, chemical composition and mechanical performance, and batch testing should be applied during production. The delivery should include the material certificates and the inspection records for the supplied parts, so that the customer can verify the products against the specification. A reliable supplier should also be able to provide the drawings, standards and test reports for the fastening system as a whole.
A common misconception is that all fastening systems are interchangeable. Clip type, tension clamp and spring blade systems have different components, clamping forces and maintenance methods, and they must be matched to the track design. Another misconception is that the clip alone holds the rail; the rail is held by the complete set of plate, pad, clip, shoulder and spike working together. It is also often assumed that standard fasteners fit any rail section; in fact each rail profile needs components with the correct foot geometry, hole pattern and dimensions.
Frequently Asked Questions
What is a rail fastening system? It fixes the steel rail to the railway sleeper, maintains the gauge and prevents vertical and horizontal movement of the rail relative to the sleeper.
What components make up a fastening system? typical system includes a rail tie plate, spike, clip, rail anchor, fish plate, pad and shoulder.
What types of fastening systems are available? Clip type, tension clamp type and spring blade fastening systems are the main types.
Can fastening systems be supplied for subway track? Yes, systems are available for high speed rail, normal rail and subway track.
What bolts are used in rail fastening? High tensile bolts with nut and washer and fish bolts with nut and washer are commonly used.
Why is the fish plate part of the fastening system? The fish plate connects adjacent rail ends so the track stays continuous and the joint keeps its strength.






